Power & Source of Big Ideas

NanoPC-T4 Fan interface

Moderators: chensy, FATechsupport

I've bought a fan to experiment with the NanoPC-T4. The connector is the same as the one shown in the image below:
Image

Unfortunately, although already quite small the connector is way to big to fit the NanoPC-T4:

Image


What kind of fan connector should I be looking for?
Second question: does the NanoPC-T4 support RPM control (i.e. low temp = no fan spinning, temp above X degrees = fan spinning)?
I ended up just going with this Fan. The price was good and it's really super quiet. It's not running off the T4 as intended, but it does keep things cool.

ImageImage
You can use this fan if you use jumber wires.
The black wire is negative, and the middle wire is positive.
Then connect negative wire to ground, and the positive to a 5V pin.

Like this.

Attachments

Wish the specified the type of connector like a micro or nano JST or something
Darkcast wrote:
Wish the specified the type of connector like a micro or nano JST or something

They do on the wiki.
It's a BM03B-GHS-TBT connector.
http://wiki.friendlyarm.com/wiki/index.php/NanoPC-T4
Check at the pin-out of the fan connector.
NicoD wrote:
Darkcast wrote:
Wish the specified the type of connector like a micro or nano JST or something

They do on the wiki.
It's a BM03B-GHS-TBT connector.
http://wiki.friendlyarm.com/wiki/index.php/NanoPC-T4
Check at the pin-out of the fan connector.

awesome man you the best :)
btw I never seen that connector in my life, do you know where I can get a fan with that type of connector ?
Darkcast wrote:
awesome man you the best :)
btw I never seen that connector in my life, do you know where I can get a fan with that type of connector ?


I think this is it. But I'm not completely sure. I can't see the connector well enough. It is a pwm fan at 12v, so if it doesn't fit you could always put the right connector on it.

Don't buy it, shipping isn't good at all. I'm looking for another one. Can't find much.
https://wholesaler.alibaba.com/product- ... 1e7at5aPV8
NicoD wrote:
Darkcast wrote:
awesome man you the best :)
btw I never seen that connector in my life, do you know where I can get a fan with that type of connector ?


I think this is it. But I'm not completely sure. I can't see the connector well enough. It is a pwm fan at 12v, so if it doesn't fit you could always put the right connector on it.

Don't buy it, shipping isn't good at all. I'm looking for another one. Can't find much.
https://wholesaler.alibaba.com/product- ... 1e7at5aPV8


Maybe best to buy a 5V fan and power it with the gpio's. I need the name of the female connector, but almost no information can be found on it.
NicoD wrote:
NicoD wrote:
Darkcast wrote:
awesome man you the best :)
btw I never seen that connector in my life, do you know where I can get a fan with that type of connector ?


I think this is it. But I'm not completely sure. I can't see the connector well enough. It is a pwm fan at 12v, so if it doesn't fit you could always put the right connector on it.

Don't buy it, shipping isn't good at all. I'm looking for another one. Can't find much.
https://wholesaler.alibaba.com/product- ... 1e7at5aPV8


Maybe best to buy a 5V fan and power it with the gpio's. I need the name of the female connector, but almost no information can be found on it.

That's my whole problem, they put the strangest connector in the world which fans are not made with and now I have to buy a fan and the connector to make them myself.. Why they didn't just use a normal fan connector.
Darkcast wrote:
That's my whole problem, they put the strangest connector in the world which fans are not made with and now I have to buy a fan and the connector to make them myself.. Why they didn't just use a normal fan connector.


I think the BM03B-GHS-TBT male connectors were at a discount because nobody else buys these things.
Maybe afterwards they found out that nobody makes the female connectors for them so `t sell fans with it. I only found the male, I searched for the female to be able to compare.

I don`t know.

A 5V fan with the 5V gpio and GND does the job too.
The mating connector is a JST part number GHR-03V-S and stocked by Digikey along with crimp pins although I would suggest getting the jumper leads and using those by soldering onto existing wires as the tooling for the crimps is likely to be expensive.

https://www.digikey.com/product-detail/ ... -ND/807815

If you want the crimp tool, it's here but check the price.

https://www.digikey.com/product-detail/ ... ND/5052067
On a side note.

What is the thickness of the thermal pad that comes with the T4, I bought an "Innovation Cooling LLC IC Graphite Thermal Pad" but it`s too thin and fell out before i even powered up with the stock heatsink screws tight, I thought of doubling it up but it`s really slippery and will not stay in place.

I suppose i would have to buy a copper shim if i wanted to use thermal paste.

Thanks

John.
A new design heatsink and fan combo is available for the NanoPC-T4 from Friendlyarm
https://www.friendlyarm.com/index.php?r ... uct_id=263

I've had it ordered for about 3 weeks now, still waiting for delivery
I ordered one of these fan/heatsinks (waiting for delivery only been 5 day`s) as well, I have the steel case and the temp are hitting 70/80c

Looks like it only has the two power wires, No fan speed wire or fan speed adjust wire.

I just hope the fan is quiet.
Tinderbox (UK) wrote:
Looks like it only has the two power wires, No fan speed wire or fan speed adjust wire.


You only need 2 wires for speed control with PWM. The 3rd wire is usually a pulse output from the fan that is used to determine the fan speed.
Fingers crossed you are right and the fan speed can be adjusted, Though a fan that speeds up and down can be more noisy than a constant speed one as you get use to the sound.

Will have to wait and see how noisy it is.
Have you got a fan working using Armbian Bionic?

Who is online

In total there are 2 users online :: 0 registered, 0 hidden and 2 guests (based on users active over the past 5 minutes)
Most users ever online was 106 on Tue Jun 04, 2019 5:48 pm

Users browsing this forum: No registered users and 2 guests