Power & Source of Big Ideas

When I enable the WiFi in the settings, this appears on the debug output. Any clues? [ 43.188000] dw_mmc dw_mmc.1: Hardware locked write error [ 43.204000] dw_mmc dw_mmc.1: Hardware locked write error [ 44.228000] dw_mmc dw_mmc.1: Data0: Never released by cmd52 [ 45.232000] dw_mmc dw_mmc.1: Data0: N...
For reference, the BIN files are located here.

https://git.kernel.org/pub/scm/linux/ke ... ee/rtlwifi

Click on them and then choose to download raw otherwise you get the text version if you right click and save.
OK, I was able to make /system read/write from ADB and copy the required binary file to the device. adb push rtl8192cufw.bin /system/vendor/firmware/rtlwifi/rtl8192cufw.bin WiFi still doesn't seem to work and doesn't detect anything when you switch it on in the WiFi settings. Mmmmm <7>[ 241.288000] ...
I have this partially working now. The RTL8188 driver was not built into the kernel. Once I did this and rebuilt the kernel and updated the Fire 3, it was able to detect the USB device but failed to complete because of a missing bin file. I have the bin file but need to do some work on the Android b...
Hello v8dave, Do you know there are any source code about android native for UART and I2C communication from FriendlyElec? They have a driver but your code needs to be signed with the platform keys. I wrote my own I2C, GPIO and UART drivers with the JNI. There are some open source options out there.
What device are you passing in for the PORT string?

On the Nano PC T3 Plus I use something like "/dev/ttysac3"
You are correct, there is no 1-wire on the eDP display and the schematic for the eDP display HD702V shows that they seem to be using I2C to talk to the STM8 that handles the LED dimming and backlight control. They must be using the I2C to detect what display is attached and adjust the kernel driver....
Hi, Has anyone managed to get the eDP interface working for a 3rd party display (i.e. not the 7" supplied by FriendyArm?) Which cables, adapters and backlight LED power supply did you use? Was a new Kernel with the proper timings necessary? I am about to embark on creating a custom display for...
DesignerDave wrote:
They are 1 3/16" tall.

Haven't you switched to metric yet? ;)

I finally got the kit this week and they were 30mm so I got some rather nice green anodised aluminium (note spelling) spacers to build my system with. The Fire3 is damned good price for performance.
As the subject says, which one has anyone got to work on this board running Android?
Fixed. I decided to use the existing image and then copy the new files over and fuse the SD card. Now I can boot my custom Android version.
I have a NanoPi Fire 3 and using the stock Android image on the MicroSD card, it boots fine but the screen is portrait so want to use the custom Android build that I have for the NanoPC T3 Plus and as the build setup is the same on the Wiki for the NanoPi Fire 3, I assumed it would work. I fused thi...
You have access to the Andoird and Android Linux source so you can potentially do anything you want right there. You can add in any SU apk and have this as part of the build. Make other changes for security etc. I recently needed a way to shutdown the Android device from code and I made changes to t...
Is there any temperature sensors available on the Nano PC T3 Plus boards that can be read with Android?
If you know how to build a JNI then there are a few options that will be easer than using the FA .so and don't need you to build with the platform keys. This one looks easy. https://github.com/chzhong/serial-android I also have one but I don't have the time just now to package it up. I will get arou...
Tiemichael wrote:
Currently I am able to root my NanoPC-T4 via adb, but it only lasts until I reboot.
I have not found a way to 'autostart' it ...

How are you doing this via ADB? What commands are you using?

I am still looking at the kernel to see if this can be done from there.
What do you see when you use this? The likely issue is that the video timing is not correct for the display. You are likely going to have to modify the Linux Kernel to add the display settings and some code to select that display. FriendlyArm auto detects the display in the kernel code so that it ca...
Did you ever get this and get it to work? I could not find any drivers on that website.

I am also looking to add audio to the Fire3.
dvoeckler wrote:
lubuntu would be ideal - but any linux works perfect for me.

I don't have anything for native coding in Lubuntu but maybe this Android JNI will help with how I manage this with Java under Android. The JNI is written in C code.

For Java, you could use the same technique used in Android but I am not sure how to create a JNI outside of the Android development environment.


I use this custom library to do basic GPIO and I2C under Android 5.1 or higher.
dvoeckler wrote:
i would really be interested - is it on github already?

I've uploaded it this morning. Sorry for the delay.


Let me know if you have any issues with getting it to work. As long as the export directory is user accessible, it should all work nicely.
Which OS?
Are you using a kernel that supports the HDMI output?
Does the HDMI connection have digital audio on the Fire3?

I plan to use with the 43" LCD but would like to have audio is possible via the HDMI connection.

Anyone know if this will work?
I am waiting for my parts to arrive and I am trying to get the length of the long standoffs so that I can get the other parts of my design completed.

They look to be 30 or 40mm.

Can someone confirm the length?
I have worked this out and I now have a JNI under Android that requires no signing with the system keys and can be run from normal app level development and no special permissions. I'll see about putting this up on GITHUB shortly if anyone else is interested. This code does basic GPIO and I2C. For P...
Has anyone been able to do GPIO read or write without using the FriendlyArm library? The library they have requires you to build your app as part of the system which makes debugging and testing virtually impossible. I have a driver from the past but the directory structure for the GPIO is different....
PS. The fact you see the FriendlyElec logo indicates that the board is attempting to boot.

Go get that USB to TTL serial converter and tell us what you found.
For the low cost of a serial debug board, it will be money well spent as it will show you clearly what is happening during the boot cycle. Without this, we have no way of helping you with this. Any cheap USB to TTL (3.3V) converter will do the job. Just connect up GND, RX, and TX from the board to t...
I left it at 60% for over 3 hours and no flickering was detected. I then bumped the brightness to 100% and it started to flicker within a few minutes. I dropped it down to 80 and the display is stable again. Just to be sure I bumped it back up to 100% and after a short time, it started to flickering...
Does anyone know if this or other NanoPis would cause emissions problems if incorporated into a commercial product? You will need to do some pre-testing yourself to determine that as the boards come without any certification. They are considered development boards and because you are likely to add ...
I've dropped it to 60% and I'll leave it running and see if it happens again but usually the display has already dimmed at the point where it starts to flicker. The eDP HD702 is the exact same LCD panel and touch as the RGB input HD702 but without the RGB to LVDS IC as it drives the LVDS directly. L...
Anyone else running the T4 with Android 8.1? I am seeing flickering on the video after a certain time and seems to correspond with the display timeout but not always. It's not a power issue as I have a bench supply running it under test with 12V and 600mA being drawn and with the power supply set fo...
Tiemichael wrote:
Found it!
Thanks for your help!

Welcome. If you fork the source and make the changes to add your LCD and it all works, would be great if you could post it online.
Thanks! I checked the entire development tree, but could not find any file or directory containing 'HD702' Search for a file called panel-friendlyelec.c in the kernel directory. HD702 is located in that file. I use Sagasu to do the search in files. Handy little program. ;) This assumes you are usin...
Great, to see that eDP is working with Android! I try to connect a 14.5 inch eDP-panel with Backlight and Touchscreen to my NanoPC-T4. Any idea which files i have to change, to get started? Thank you! I think all the changes you need to do are in the kernel and to do with timing and to bypass the a...
The source for the kernel is also now added to GITLAB.

I enable and disable this from the PWM driver for the backlight. Probably an easier place to do this but for now this is reliable way to handle the enabling and disabling of the doubletap2wake feature.
I got to work in regards to getting touch detection but I still need to hook in the video drivers so that the doubletap2wake gets enabled when the display is off and disabled when the display is on. So far, I've not been able to find the correct place to do this. I can't see to find somewhere the pa...
I am trying to implement double tap to wake on the Nano PC T3 Plus but not getting anything from the underlying driver. I have implemented the code from here: https://git.sphere.ly/varun.chitre15/thunderzap_sprout/blob/b61590e8285ef421e7e0dbfde694b2d4e8643ae1/drivers/input/touchscreen/doubletap2wake...
Wow! An amazing contribution! I will be checking it out! Question: does this build have root access? Seriously, thank you. Let me know if you can compile it without errors. I have been able to clone it with another VM machine but cannot build it. I am trying to work out of this is a GITLAB upload i...
davidjohn wrote:
I haven't any word to value this post.....Really i am awed from this post....the individual who make this post it was an extraordinary human..thanks for imparted this to us. blog comments

Spammer. I saw your gig on Fiverr and I will be reporting you for spamming. !!
If you build the source and choose the USERDEBUG version (default), you have full root access.
This is the place I found the info. Other stuff may help.

https://stackoverflow.com/questions/170 ... aries-libz
I think you many still be missing some system files. A search threw up this one as a possible solution.

sudo apt-get install lib32z1
I have managed to copy the new image files to the SD card via ADB via the use of an external flash disk. Now I want to reboot the module as if the BOOT switch was pressed as I am unable to press this button without disassembly. Anyone know if there are any commands I can use from ADB to do this on t...
Which version of Ubuntu are you using?

I can't get nanopi3 to build under 16.04 or higher so had to create a VM with version 14.04 instead and it compiles fine. I have made changes to add GSM and landscape etc and it all builds fine.
Just put the SD card with Android into the machine and it will write over the previous data.

I tested my T4 with Ubuntu at first and now running a custom Android on it. No need to "clean" anything.
I didn't jot them all down as I was doing the work (I know, ny bad) but this is a list that I can remember. Changes to support Landscape more for the boot animation and have the UI in landscape. Still an issue with the initial stage of the boot animation that I have not tracked down but as it doesn'...